Описание отличия различных технологий генераторов Озона
http://curezone.org/forums/fm.asp?i=1495716
There are three ways to generate ozone: Ultraviolet (UV), hot corona and cold corona. Here are the pros and cons to each:
UV- Pros: The least expensive of the units averaging around $300. They will form higer allotropes of oxygen though, known as cascading ozone or polyatomic oxygen molecules. Cons: These units mimick sunlight, which means they also form nitrogen and sulfur oxides in the presence of air, which form the corresponding acids when reacted with water. The tubes deteriorate with time reducing output, and they are very difficult to regulate their output. They ARE NOT recommended for therapy internally.
Hot corona- Pros: A mid range priced machine, averaging $500-900. These machines are stronger than UV, and more easily regulated. Cons: They also form nitrogen and sulfur oxides in the presence of air. They only form O3, which is not as strong as the higher allotropes. They are not recommended for therapy internally.
Cold corona- Pros: Can be regulated and does not form acidic precursors in the presence of air. Forms O3 and the higher allotropes. This is the type of Ozone Generator recommended by German doctors for therapy. Cons: The most expensive units and hardest to find. Average cost for these units is $1500-15,000.
One of the biggest problems with trying to find a cold corona unit is that many manufacturers selling "cold corona" units actually have hot corona units. The confusion comes from the tube design. In general a hot corona design has one dielectric between the electrodes. Cold corona tubes use two dielectrics preventing exposure of the gas to either of the electrodes. The problem is that is all based on the older pig iron high voltage transformers. With the introduction of the newer high frequency solid state transformers all of the above gets thrown out. The higher frequency drops the resistance of the dielectrics in essence converting the cold corona tube back in to a hot corona design. Manufacturers use these transformers because they are lighter, smaller and allow for wider spacing between the electrodes. So unles you know what you are looking at it is hard to tell if a "cold corona" device is really a cold corona device.
As far as building them, it is a really simple thing to do, just very tedious. It is basically two metal electrodes insulated with two pieces of glass encased in a tube with hose barbs on each end to allow passage of the oxygen. The metal electrodes are connected to a high voltage transformer (pig iron type)with a voltage of 7500-9000V 20-30ma. You can use neon transformers for this.
As for the oxygen, welding supply companies provide the tanks through either purchase or rental. All oxygen sold has to be medical grade regardless of its use under Federal law. You will have to buy a regulator though since they do not rent these. But a hose barb for the regualtor to fit your tubing for the unit. Altogether the tank, regulator and hose barb should run just under $200.
http://www.synergyozone.com/
The WPS-400 Medical Ozone Generator is an ideal source for creating ozone for use with ozone therapy. Potential uses of ozone therapy include drinking ozonated water, insufflations, in combination with steam or far infrared and more. The WPS-400 includes two ozone chambers that can be used independently (for lower ozone levels) or together (for higher levels of isotopes such as O8, O12, O13, etc). Each chamber has its own on/off switch and regulator. The WPS-400 Ozone Generator is fed by an oxygen source, either an oxygen tank or oxygen concentrator (sold separately). The unit takes the oxygen coming in and transforms it from two molecules of oxygen to three molecules (O3). Since ozone is very unstable, after about a half hour after it is made, the ozone molecules break up again into one stable oxygen unit and one singlet oxygen molecule. It is this singlet molecule that does the work in ozone therapy. The WPS-400 Ozonator has a unique quartz glass cold corona tube that does not come in contact with metal and will not generate a significant amount of heat. It comes standard with ozone resistant silicon outlet hoses. It is ideal for any dental, hospital, laboratory, medical, veterinary or home clinic application that requires dependable and stable ozone production and is built to last for years without any maintenance. The WPS-400 Ozone Generator is superior in quality, performance, reliability, and workmanship to all others on the market. The front control panel includes a variable control selector switch for each individual chamber that allows for an unlimited number of output settings. There are two inlet and two outlet hose barb fittings which will take a 3/16" silicone hose.
Features of the WPS-400 Medical Ozone Generator:
• Cold Corona Ozone Discharge - a low voltage, cold process. No cooling fan is required. Unit has no moving parts. Generator is affordable, compact, portable and very easy to operate.
• Each chamber has its own regulator and on/off switch to adjust ozone levels (ozone levels are also adjusted by changing oxygen flow)
• Built for continuous, efficient and silent operation in harsh environments.
• Dual phase electrical short circuit protection.
Концентратор Кислорода для генератора http://www.internetcorkboard.com/search.php?q=oxygen%20concentrator
http://www.internetcorkboard.com/search.php?q=oxygen%20concentrator